Cubic yards to tons soil.

Materials Calculator. Whether excavating a trench or a hole for a tank or foundation, or stockpiling materials such as gravel or soil, there is often a need to make a field estimation of volume and weight. To fulfill this need, HTG developed a materials calculator using common measurements. The calculator conservatively assumes a relatively ...Calculate #89 Gravel Stone (P1) Type in inches and feet of your project and calculate the estimated amount of Gravel Stone in cubic yards, cubic feet and Tons, that your need for your project. The Density of #89 Gravel Stone (P1): 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t. Type in your numbers. A:Uncategorized. Multiply the bulk density of topsoil to convert cubic feet to pounds, then convert cubic feet to tons. For a mass of 8,964 pounds, this is 83 pounds per cubic foot by 108 cubic feet. Because there are 2,000 pounds per ton, the conversion from yards to tons is 8,964 by 2,000, or 4.5 tons. In terms of cubic yards, how many cubic ...Use this online gravel calculator to estimate how much gravel in volume (cubic ft, cubic yards, or cubic meters) or weight (tons & pounds, tonnes and kilograms). It uses a standard pea gravel density. Unit system. Imperial (in, ft or yd, lbs and tons) Metric (cm or m, kg and tonnes) The area to fill is. Rectangular.

Cubic Meters. A metric unit of volume, commonly used in expressing concentrations of a chemical in a volume of air. One cubic meter equals 35.3 cubic feet or 1.3 cubic yards. One cubic meter also equals 1000 liters or one million cubic centimeters.A typical ton of condensed soil is around 3/4 cubic yards or 20 cubic feet. When measuring soil, it is important to take into account the moisture level. Placing a ton of soil in a dry area will not have nearly the same weight as when placing the same ton of soil in a humid area.

The truck’s cubic feet or storage capacity is determined by multiplying the dump body’s dimensions of width, length, and height. To get cubic yards, divide that number by 27. The average full size dump tuck has a dump bed that is 7 1/2 feet wide, 3 1/2 – 4 1/2 feet tall, and 10 ′ – 18′ long. They now have a capacity of between 7 and ...

Gravel, wet 1/4 to 2 inch - 1.69 tons/cubic yard. Depends on the type of gravel. I will show an example using loose dry gravel from the above list... 416 cubic yards * 1.28 tons/cubic yard = 532.48 tons (U.S. short tons) Just replace the density with the correct density from the list, depending on the type of gravel.We are going to use this formula : Length in feet x width in feet x depth in feet. Once we have the volume, we divide that number by 27, the number of cubic feet in a cubic yard. If you are looking to convert the total into tons, the you have to divide the total volume by 21.6, the number of cubic feet that fits in a ton. Enter this information ...Jan 20, 2021 · We are going to use this formula : Length in feet x width in feet x depth in feet. Once we have the volume, we divide that number by 27, the number of cubic feet in a cubic yard. If you are looking to convert the total into tons, the you have to divide the total volume by 21.6, the number of cubic feet that fits in a ton. Enter this information ... For example, if we assume a density of 100 pounds per cubic foot (1602 kg per cubic meter) for the sand, then 1.5 tons of sand would have a volume of approximately 30 cubic feet (0.85 cubic meters). Which is very close to a cubic yard. ... 1 cubic yard of soil is a volume measurement of dirt, sand, or other types of earthy materials. It ...

The company that fertilizes my yard said that I needed to add an inch of top soil on the lawn since the roots were showing. After 30 bags of 1 cubic ft top s...

I recently had to buy some fill dirt. I got 9.68 tons, and surprisingly, it really isn't as much as you might think. I thought I'd make this video to show ev...

Jan 14, 2024 · This will vary by type of material as well as moisture content. Dry soil has a lower density than wet soil. Stones and sand have a higher density than soil. One cubic yard of dry loose soil weights about 1 – 1.3 US tons (1 US ton = 0.9 metric ton), while one cubic yard of wet or compacted soil weighs between 1.5 and 1.7 US tons. Circle Area: Mulch, Dirt & Topsoil Calculator to Estimate Cubic Yards Required: Enter the radius in feet: Enter the depth in inches: Your Estimate is. Other Estimation Calculators. Calculate Cubic Yards for Mulch or Dirt. Calculate Cubic Yards for Circles of Mulch or Dirt. Calculate Tons for Sand, Gravel or Limestone.Cubic Yard Calculator. We sell all of our online materials by the cubic yard. A cubic yard is equal to 27 cubic feet. You can use the online calculator to determine how many cubic yards of material are required. As a general guide, 1 cubic yard of aggregate, sand, or dirt is equivalent to 1.5 tons.Whether you are a homeowner looking to maintain a lush garden or a farmer wanting to maximize crop yield, understanding the health of your soil is crucial. One of the first places ...If the topsoil is dry and sandy, it can weigh around 2,600 lb (1,200 kg) per cubic yard. Clay soil is lighter at around 1,700 lb (770 kg) per cubic yard. Topsoil is used for most home and garden projects like raising flower beds, reshaping lawns, and adding more nutrients to your yard’s soil. 2. A yard of wet topsoil can weigh up to 3,000 lb ...Calculate Fine Mason Sand. Type in inches and feet of your project and calculate the estimated amount of Sand / Screenings in cubic yards, cubic feet and Tons, that your need for your project. The Density of Fine Mason Sand: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t. Type in your numbers.

Yard To You is a unique Home Depot delivery program that brings bulk quantities of lawn and garden product right to your home or project site. Getting started is easy. Select your product and amount, and order it online or in- store. Within 24 - 72 hours, a Home Depot certified vendor will contact you to schedule the mulch or garden soil ...How to convert cubic yards to metric tons (or tonnes)? To convert cubic yards to metric tons (or tonnes), multiply the cubic yard value by 0.752294. Conversion formula: metric tons (or tonnes) = cubic yards × 0.752294.Calculate Red Clay. Type in inches and feet of your project and calculate the estimated amount of Soil & Dirt in cubic yards, cubic feet and Tons, that your need for your project. The Density of Red Clay: 2,000 lb/yd³ or 1.00 t/yd³ or 1.0 yd³/t. Type in your numbers.Calculate Salt-Sand mixture. Type in inches and feet of your project and calculate the estimated amount of Road Grit / Salt in cubic yards, cubic feet and Tons, that your need for your project. The Density of Salt-Sand mixture: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t.The weight of 2 yards of topsoil depends on its density, but it can range from 2,500 to 3,500 pounds (1.25 to 1.75 tons). How much does 3 yards of gravel weigh? The weight of 3 yards of gravel depends on the gravel’s density but typically ranges from 3,000 to 4,500 pounds (1.5 to 2.25 tons). How many cubic yards make a ton?The volume of the center prism: 0.5 * A * B * H. V = the volume in cubic feet. A = length A. B = length B. H = height. The two results are added together for a cubic foot value and converted to cubic yards by dividing the cubic feet by 27. Enter the height of the pile and the base length of the pile in feet.

It is a material property called density and it will vary with material. Most broken rock of relatively uniform size and dry is about 1.3 ton/yd³, with a little variation. Wet and mixed material (sand & gravel) can be more, 1.4 - 1.5 ton/yd³ because the spaces between aggregate get filled. Fill dirt may be close to the same number.

We are going to use this formula : Length in feet x width in feet x depth in feet. Once we have the volume, we divide that number by 27, the number of cubic feet in a cubic yard. If you are looking to convert the total into tons, the you have to divide the total volume by 21.6, the number of cubic feet that fits in a ton. Enter this information ...4.5 cubic feet of compost (4.5 20-quart bags) 1.5 cubic feet of soilless potting mix. 1.5 cups Gardener's Supply granular organic fertilizer. Before placing your raised garden beds in their permanent location, be sure to remove any grass or perennial weeds from the area. Use a garden fork or shovel to loosen the native soil to a depth of 6-10″.To calculate cubic yards we use the formula: Cubic yards = Length (ft) x Width (ft) x Depth (ft) ÷ 27. Measure the length, width and depth of your area and then multiply the figures together to calculate a result in cubic feet. Dividing the result by 27 will give you a total in cubic yards. Cubic yards = Length (ft) x Width (ft) x Depth (ft ...It will calculate the volume increase of the material using the swell/bulking percentage from Bank to Loose volume. Truck loads come in large range of sizes. 9 tonne Tipper truck 6 cubic metres of sand or gravel up to 9 cubic metres of mulch. 6 wheeler truck 10 cubic metres of sand or gravel and up to 15 cubic metres of mulch.While a half-ton truck can fit 2 yards of dirt in the bed, that will easily exceed the payload capacity of the truck and cause damage. Here’s how much dirt a half-ton pickup can actually carry: Dirt / Topsoil: 1-1.5 cubic yards. Sand: 3/4-1 cubic yard. Gravel: ¾-1 cubic yard. Mulch: 2-3 cubic yards. Here are some things to keep in mind:Here are the conversion factors at a glance: 1 yard = 27 cubic feet. 1 cubic foot = 0.037 cubic yards (rounded to three decimal places) For example, if you have 100 cubic feet of soil, dividing by 27 gives you approximately 3.704 cubic yards. On the other hand, if you have 5 cubic yards of soil, multiplying by 27 gives you 135 cubic feet.Mulch Calculator. Enter the approximate length and width of the area you want to cover, then the desired depth (standard depth for mulch is 3"), then click Calculate. The calculator will tell you approximately how many cubic yards of mulch you'll need (based on typical coverage of 100 sq. ft./cubic yard, 3" deep). Width (ft) Length (ft) Depth ...

depth = 9 inches ÷ 12. depth = 0.75 feet. Next, calculate the volume in cubic feet. cu ft = 12 ft × 14 ft × 0.75 ft. cu ft = 126 cu ft. Finally, convert the volume in cubic feet to cubic yards. cu yds = 126 cu ft ÷ 27. cu yds = …

14 Jan 2022 ... Generally speaking, 1 tonne of topsoil will cover 0.63 cubic metres or 22 cubic feet or 0.81 cubic yards. Our bags of topsoil come in sizes ...

Calculate Deicing Salt. Type in inches and feet of your project and calculate the estimated amount of Road Grit / Salt in cubic yards, cubic feet and Tons, that your need for your project. The Density of Deicing Salt: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t. Type in your numbers.Calculate Mason Sand. Type in inches and feet of your project and calculate the estimated amount of Sand / Screenings in cubic yards, cubic feet and Tons, that your need for your project. The Density of Mason Sand: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t. Type in your numbers.A cubic yard of topsoil weighs 1,080-2,000 pounds when it is dry. Wet topsoil is much heavier and 1 cubic yard can weigh up to 3,000 pounds. The average pickup truck with an 8'x5.33' bed can fit 1-2 ½ cubic yards of dry topsoil. However, the actual weight of a cubic yard of topsoil will depend on its moisture content and the amount of ...Short Ton (US) to Cubic Yards: Tons / 1.4 = Cubic Yards. Long Ton or Freight Ton to Cubic Yards: See also Boat Tonnage Calculator Online. Tons / 1.1326 = …Circular Area Calculator. We sell all of our online materials by the cubic yard. A cubic yard is equal to 27 cubic feet. You can use the online calculator to determine how many cubic yards of material are required. As a general guide, 1 cubic yard of aggregate, sand, or dirt is equivalent to 1.5 tons.Home. Construction Calculators. Measurement. Cubic Yard Calculator. Enter the length, width, and depth, or area and depth of the space below to calculate volume in cubic …Sand Calculator. Calculate how much sand you need by drawing and measuring the areas you want to cover directly on a Google satellite map. Typical range between 4" and 12". Depending on market, amount and type of sand the range is between $20/yd³ and $150/yd³. Minimum quantity is usually a cubic yard which requires a truck to load it. This calculator lets you input your coverage needs for the garden and the cost per cubic yard to estimate the total spend. It’s great for budgeting topsoil purchases. Just input Area (sq ft), Thickness (in), and Cost per Cubic Yard ($) to get the Total cost of topsoil. Pro Tip: Call around for quotes, as prices can vary quite a bit between ... Material and Quantity. The cost of topsoil typically ranges from $10 to $50 per cubic yard. Your total soil cost will vary based on the quantity needed, often measured in cubic yards. You may opt for bulk topsoil costs if you need a large volume, which may be economical in some cases.Click here to determine your cubic yard capacity. Soil Building Systems produces organic compost, hardwood mulch and soil mixes for the landscaping industry. SBS is based in Dallas, TX. Call 972-831-8181.Calculate 21AA Crushed Concrete. Type in inches and feet of your project and calculate the estimated amount of Recycled Materials in cubic yards, cubic feet and Tons, that your need for your project. The Density of 21AA Crushed Concrete: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t.

Calculate #4 Limestone. Type in inches and feet of your project and calculate the estimated amount of Limestone Gravel in cubic yards, cubic feet and Tons, that your need for your project. The Density of #4 Limestone : 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t. Type in your numbers.depth = 9 inches ÷ 12. depth = 0.75 feet. Next, calculate the volume in cubic feet. cu ft = 12 ft × 14 ft × 0.75 ft. cu ft = 126 cu ft. Finally, convert the volume in cubic feet to cubic yards. cu yds = 126 cu ft ÷ 27. cu yds = 4.67 cu yds. If you are calculating yardage for a concrete or landscaping project, understand that suppliers may ...Nov 21, 2023 · The weight of a cubic yard of topsoil can vary depending on its moisture content and composition. On average, dry topsoil weighs about 2,000 pounds per cubic yard. However, it’s important to note that the weight can range from 1,000 to 3,000 pounds per cubic yard. To determine the weight of a cubic yard of topsoil, you can use the following ... Instagram:https://instagram. master lock bluetooth lost activation codedarien lake free ticketsamazingtransformationcomicsauthorized troy bilt service center Coverage Chart. We sell all of our online materials by the cubic yard. A cubic yard is equal to 27 cubic feet. You can use the online calculator to determine how many cubic yards of material are required. As a general guide, 1 cubic yard of aggregate, sand, or dirt is equivalent to 1.5 tons. Coverage Chart. hair salons brandon msirving accident today A cubic yard to ton calculator works by converting volume measurements (in cubic yards) to weight measurements (in tons). Here's how it typically works: Input: You input the number of cubic yards of a material into the calculator.This could be any substance that you're measuring, such as soil, gravel, sand, concrete, or any other material sold or used in bulk.Calculate Fill Dirt. Type in inches and feet of your project and calculate the estimated amount of Soil & Dirt in cubic yards, cubic feet and Tons, that your need for your project. The Density of Fill Dirt: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t. Type in your numbers. maryland hourly paycheck calculator Short Ton (US) to Cubic Yards: Tons / 1.4 = Cubic Yards. Long Ton or Freight Ton to Cubic Yards: See also Boat Tonnage Calculator Online. Tons / 1.1326 = Cubic Yards. These formulas are straightforward yet pivotal for converting weight to volume, catering to different units of tonnage used across the globe.Next, decide on the depth or thickness of your garden's topsoil layer. For this, let's assume this value to be D = 0.5 yards. Multiply the depth with the area to get the volume: V = 200 x 0.5 = 100 yd3. This is the volume of soil needed to cover an area that has a length of 20, a width of 10 and a depth of 0.5 yd.Cubic yard. Definition: A cubic yard (symbol: yd 3) is an imperial and United States Customary unit of volume defined as the volume of a cube with measurements 1 yd × 1 yd × 1 yd.It is equal to 27 cubic feet, 0.7645549 cubic meters, and 764.5549 liters. History/origin: The cubic yard is based on the international yard, which was adopted in the 1950s and 1960s, and is equal to 0.9144 meters.